|
|
新建网页 1
|
SPE-QM2430 Dia 6"
Cylindrical Screen Printing Press
|
 |
 |
 |
|
Curved screen printing machine is mainly used for
printing cylindrical type, cone type products; Such as a variety of
plastic, glass, metal materials made of cylindrical, conical shape
products, including wine bottles, medicine bottles, cosmetics bottles
and other packaging bottles; Mugs, thermos mugs, beer mugs, red mugs,
etc. Glass tube, pen ,ballpoint pen, fishing rod, bat and other small
cylindrical products; Pure bucket, paint bucket, alcohol bucket, paint
bucket, oil and lubricating oil bucket and other large packaging
cylindrical products. |
 |
|
For cylindrical or conical type products, the
printing surface has a large concave or convex, the printing surface has
spots and other non-plane printing is not suitable for the machine. |
 |
|
This curved screen printing machine is mainly used for printing
cylindrical and conical products with a diameter below 150 mm.
The maximum printing height of the machine is 270 mm, the length of the
arc is 380 mm.
|
 |
|
This machine adopts the printing screen frame
height positioning structure, the front part is equipped with the
parallel placement plate, the whole machine is firm and stable in the
printing process. Printing materials and tools such as ink buckets can
be placed on the rear horizontal board of the main machine. |
 |
|
The printing plate frame uses the spring to pull and lift, matches the
flower basket screw to adjust the lift strength of the screen plate ,
the lift angle of the screen plate can be controlled by adjusting knob,
the operation is easier. The spring tension on both sides of the machine
should be as consistent as possible after installation , otherwise it
may cause distortion of the printing screen frame.
|
 |
|
It is easy to install and remove the screen frame.
Just put the screen plate into the back support plate from below of the
printing plate rack, and then put the screen plate into the front
support plate, tighten the screen plate fixing screw. (limited to the
design requirements of the machine, the screen board of the machine must
use the screen frame with the outer diameter of 560*410 mm and the
height within 30 mm.) 2 screen frames are attached to the machine. |
 |
1.Place the screen frame into the rear support
plate from the bottom of the installation table.
2.Move the front of the frame to the front support plate, tighten four
Screws to fix the screen frame.
6 sliders connected to the optical axis to make the screen frame slide
back and forth,it is easy and smooth to push and pull.
|
 |
|
The back and forth sliding distance of the frame
can be controlled by the positioning ring on the optical axis; The user
can lock the positioning ring after adjusting the position of the screen
plate and the substrate placement table. Especially add the collision
rubber ring between the locating ring and the slide block, which can
prevent the slide block from directly contacting with the metal locating
ring during the back and forth sliding of the screen frame, and prevent
the sound of metal striking with each other, and meanwhile protect the
metal parts. |
 |
|
The printing scraper rack and the return ink rack
adopt the double board clip type, the installation and unloading is
convenient and quick, two sides of the main frame and the frame connect
the screw middle additional spring, in the printing process, user can
adjust the printing scraper and the return ink plate pressure according
to the need. |
 |
1.Open the scraper mounting plate
2.Put in the scraper rubber, the lower edge of the scraper and the mesh
surface will fit smoothly and smoothly.
3.Fix the following three screws (don't tighten them); tighten the top
two white knobs to fix the scraper tape.
Push and pull handle can be installed vertically or in parallel
according to the operator's needs |
 |
|
Substrate placement platform adopts knob lifting
and locking structure. Substrate placement platform can be controlled by
the lifting handle under the placement stage, first release the knob on
both sides of the baffle, lift to the appropriate height, the locking
knob on both sides of the baffle can be tightened to stabilize the
lifting platform at this height, substrate placement platform on both
sides of the height is consistent or not can be adjusted by the concave
teeth on both sides of the baffle. |
 |
Bottom of the substrate printing rack is designed
around back and forth mobile , the three long aluminum bars in the
bottom installed in the lifting placement platform, both sides are
substrate placement rack installation bar, the middle is the substrate
limit column installation bar.
Substrate placement rack installation bar can be moved around 140 mm
back and forth, in order to move as accurate as possible, according to
the concave tooth on the placement table to make parallel movement. |
 |
|
Limited post is installed on both sides of the
substrates limited post installation bar, after adjusting all printing
steps, place the substrate in the printing rack, move two limited posts
respectively to the two ends of the substrates and substrates surface
with 1-2 mm spacing (Note: not too close please , otherwise it may
affect the rotation of the substrates), using a wrench to tighten the
limited post. |
 |
Main functions of the limited post:
1.Improve the accuracy of substrate placement, ensure that all printing
positions are basically the same after substrate placement, and avoid
deviation of printing positions caused by different substrate placement.
2.Substrate placement faster, no need to mark or manually adjust,
directly put into the substrate.
3.Limit the substrate in the printing process does not deviate.
There are two sets substrate placement wheels, one
set is diameter of 50 mm blue rotation wheel, the other set is diameter
of 26 mm white rotation wheel, two sets rotation wheel can be installed
in the placement of the main frame and additional frame, users can
replace according to the needs of adjustment. |
 |
|
The attached plate configured by the machine is
used in conjunction with the substrate placement in the main frame,
which is mainly used for printing products with conical shape. The
attached plate can be connected with the main frame vertically with two
screws, or cross connected with the italic body of the main frame with
one screw. |
 |
The machine has been fully adjusted before leaving
the factory. The customer only needs to install the spring and screen
frame landing board for use.
The main body of the machine uses advanced electrostatic spraying metal
surface treatment, acid and alkali resistance, corrosion resistance,
clean resistance, no rust, can be used for a long time; Some parts are
made of stainless steel and aluminum alloy.
Equipped with a full set of installation tools and detailed installation
instructions; Easy installation without additional tools.
Export to Europe and America standard fumigation-free wooden box
packaging, all kinds of metal parts in the box are individually packaged
or placed in isolation to ensure that all kinds of metal parts do not
contact directly. |
 |
 |
|
Item included(006596):
1*SPE-QM2430 Dia 6" Cylindrical Screen
Printing Press
|
新建网页 2
|
.gif)
