Office Machine & Supply>
151005:Semi Auto Circuit Board Cut Foot Machine Lead Wire Cutting Machine 220V
Unit:
pc
Price:
C $1,379.00
Weight:
97.00kg
QTY:
     

Similar products

030000:Parchment paper

170810:106 Electric Saddle Stapler

030002:Isolating film - 20 sheets/pack

030037:Photosensitive ink - 5 bottles/set

030024:42MM Rubber Stamp Pad 20PCS

https://buyyou.net/cbe/data/prd/152/252/QQ%E6%88%AA%E5%9B%BE20170725133912.jpg

220V  Semi automatic PCB foot cutting machine

http://topseller365.com/data/prd/151/005/a.jpg

The breadboard wipe cutting machine is mainly applied in cutting the unwanted pin after the welding of parts of apparatus and this machine is assembled by parts made with exquisite craftwork. The key parts are dealt with grinding , and the imported bearing assembled wipe cutting machine grinding consistency is excellent, the rotating   speed of blade is fast and is very efficient and convenient to operate with   little noise. The double lead rail is adjusted synchronously , the height of wipe cutting is adjustable and the outlook is attractive. "Continuous improvement, lasting and efficient, clients first" is our quality tenet, it is our honor to serve you.

Instruction of adjusting

1.Open the package and read the instruction carefully and check the accessories (refer to term 7 in the instruction)
2.Check the body of machine for any abnormal phenomena, if so , contact the local agent as soon as possible
3.After conforming the good connection of the case earth, plug in.
4.First adjust the double lead rail travel route biggest, unscrew the gland bush screw(gland bush screw is right-handed screw )with 8# inner hexagonal wrench counterclockwise,take out the blade gland bush and clean up both sides of tool apron, blade, gland bush with clean and soft cloth. Then place gently the blade on the base(surface up). Next ,place the blade gland bush on the blade, screw down the gland bush screw with 8# inner hexagonal wrench clockwise. When unloading the blade, use the enclosed dismantled stick to fix the tool apron.
5. Rotate the adjusting hand wheel, adjust the width between the lead rails, and place one wanted placode of wipe cutting machine on the entrance and exit port respectively. Rotate the hand wheel until the placode at both ports slide properly in the lead rail.
6.Four sets(three screws per set)assembling screws that are equipped on top of lead rail bland bush are used to adjust the thickness of placode. During the adjusting first unscrew three perch screws among them and put placode inside and then adjust two lower order screws besides until they fit and screw down the middle screw. Operation are the same for four sets and adjust placode to slide properly inside the lead rail
7.Adjusting of height of wipe cutting machine : screw down lead rail retaining screw and adjust the big screw cap until the distance between blade and lead rail meets the requirement then screw down lead rail retaining screw. When adjusting lower avoid any friction between lead rail and blade for fear of damage to blade.
8. The height of wipe cutting of wipe cutting machine was adjusted as 1.5mm when it leaves factory and the thickness of textile board was adjusted as 1.2mm. When adjusting is necessary please adjust according to method mentioned above.

Features
https://buyyou.net/cbe/data/prd/151/005/111-1.jpg

      Blade jitter small

      Pin cutting leveling
 

     The 3 hole blade gland uses the triangle positioning principle, the blade is firmly fixed, not easy to loose, the high speed running condition, the blade does not slip, the operation is smooth, the cutting foot is accurate, the safety factor is high.
 

https://buyyou.net/cbe/data/prd/151/005/222-2.jpg
https://buyyou.net/cbe/data/prd/151/005/333-3.jpg

     The whole machine is steady, low noise and low jitter.
 

     The feeding guide rail of the fine steel is of high thickness, wear resistance, not easy to deform and prolong the service life of the machine.
 

https://buyyou.net/cbe/data/prd/151/005/444-4.jpg
https://buyyou.net/cbe/data/prd/151/005/555-5.jpg

    Line type cutting.

Specifiction
https://buyyou.net/cbe/data/prd/151/005/8.jpg
https://buyyou.net/cbe/data/prd/151/005/7.jpg
https://buyyou.net/cbe/data/prd/151/005/4.jpg

Notice: We send a blade($350) as a gift.

Operations

1. Place the welded breadboard on the adjusted wipe cutting machine and insert the lead rail down the leading-in of lead rail.
2.Push dexter feed hand shank and push placode advance at constant speed

3.Repeat step 1,2 and finish cutting the welded placode.

Notice: When the placode moves avoid moving too fast, and moving too fast can directly shorten the use life of blade and even endanger safety.

Maintenance
Wipe cutting machine is the mechanic equipment of high accuracy and with high speed and the constant maintenance prolongs its use life

1.The rotating part needs constant lubrication.

2.Clean up the cut pin

3.If the transmitting triangle strap is damaged, it needs immediate replacement and the specification is (0-450)
4.The blade should not leave cutter head for too long, lubricate the cutter head when necessary if it leaves for several days.

Notice

1.When the machine is in operation avoid putting hands into the machine.

2. This machine must work in the state of good earth connection

3.Cut off the power when installing or dismantling blade or in case of emergency

4.Cut off the power in sace of a blackout.

5.This machine should not be used in humid, flammable, corrosive, dense bug dust-filled environment.

6. Non professional repairmen are not allowed to dismantle the cover to repair it personally .

7.Do not open the cover when the machine rotates.

8.Operate the machine according to instruction strictly; otherwise out factory takes no responsibility.

Item Include(151005)
  • A set of 220V?Semi automatic PCB foot cutting machine
  • A set of Blade



 

无标题文档

About Us Product Service Shipping Payment Privacy refund Warranty

Copyright ASC365.com All Rights Reserved