|
|
|
6613Lbs/3000kg Pneumatic Punch
Machine |
|
|
|
|
|
|
 |
 |
|
Product Features: |
|
The pneumatic press is the high-pressure
gas produced by the compressor, which is transported to the
solenoid valve through the gas pipe. The working state of the cylinder
is controlled by the movement of the solenoid valve through the switch,
and the punching is completed.
1 .Compressed air as power source, high efficiency
and easy operation, can reduce labor, can be applied to manual operation
integration, automated assembly line .
2 .Simple structure, convenient operation, cheap price, superior
performance, no noise produced during the hydraulic system and electric
standby, can save electricity consumption reduce production cost, has
the very high cost
performance .
3. Easy adjustment of output, need to adjust the air pressure is
adjustable up to the required pressure, high yield .Equipped with guide
plate, high accuracy, can adapt to high speed precision impact load .
4.According to different products or mould, adjust the speed, and the
size of the pressure and stamping time .
5.Optional manual switch control, with emergency stop switch, can also
be controlled by a controller.
6.Microcomputer control system, can choose manual, semi- automatic and
fully automatic operation. |
|
Specification : |
|
Voltage |
110V |
|
Pressure |
6614lb/3000kg |
|
The die hole diameter |
0.98inch/2.5cm |
|
Working Countertops Size |
15.7*10.2inch/40*26cm |
|
Outer diameter of trachea |
0.39inch/0.1cm |
|
Booster cylinder specification |
3.94inch-0.39inch/100mm-10mm |
|
Working
air pressure |
0.5-0.8MPa |
|
 |
|
Range of application: |
Suitable for electronics, electrical
appliances, instruments, meters, cameras, watches, jewelry, hardware
and garment, shoes and hats. |
 |
|
Machinable materials: |
|
For sheet, strip, coil to shear, punching,
blanking, forming, bending, riveting, etc;Suitable for non-ferrous
metal, plastic parts processing . |
|
Detail: |
 |
Air source processor, through the pressure gauge at any
time to observe the change of air source pressure, effective separation
of water, oil and other impurities in the air, air purification, improve
the service life of the machine. |
|
Widened and enlarged work surface with 1.9 "diameter
blanking hole, 4 T-slots for easy securing of items. |
 |
 |
A clamp with an inner diameter of 0.98 ", equipped with a
guide plate, is more precise and stable. |
|
Two-handed switch, two-handed operation, safer. Equipped
with emergency stop switch, one key stop, more efficient. |
 |
 |
Equipped with a controller, easy to switch between manual
operation and automatic operation .(single cylinder machine, just set 1,
2, 3 section number. 1 is the pressing time setting; 2 is the second
time to increase the setting; 3 is the return time setting) |
|
Note: 1. 46# antiwear hydraulic oil should be added to
the hydraulic cylinder. It is recommended to replace the hydraulic oil
after one year of use. (Due to ex-factory debugging, there will be a
small amount of hydraulic oil in the machine, please prepare your own
hydraulic oil after receiving the goods).
2.Check whether the machine bolts are tightened before working. If
they are loose, they must be tightened before working.
Check whether the air pipe is properly connected to prevent air leakage
and make the machine unable to work normally.
3. Avoid placing your hand under the punching shaft during work to
avoid accidents .
4.Do not wipe the machine with a damp cloth to avoid rusting the
machine .
5.When disassembling, installing and adjusting the mold fixture, the
machine must be turned off, and standby operation is strictly prohibited
to avoid personal injury .
6.The rated pressure of the air compressor is 0.8mpa. The capacity of
the air compressor storage tank is about 60L,the larger the capacity,
the longer the service time and the more stable it is. The displacement
is optional 200L/min, the larger the displacement, the larger the
applicable machine model.
7.Note :The actual output pressure is about 80% of the theoretical
pressure. |
|
Item Number: 6613Lbs/3000kg Pneumatic
Punch Machine 230238 |
|
|
You can make
order with no worry.
Any concern just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from
us with low cost. |
|
