|
|
|
Chicken Feed Pellet Mill Machine
4MM |
|
|
|
|
|
|
|
Feed granulator
is widely used in large, medium and small aquaculture, grain feed
processing plants, livestock farms, poultry farms, individual farmers
and small and medium-sized farms, farmers or large, medium and small
feed processing plants.
This machine can
be used alone, and customers who need it can also match it with a straw
cutter for better results. |
|
 |
|
Note:
1. Before using the
machine, it is necessary to adjust the screw of the pressure roller to
the appropriate position. The pressure roller and the pressure plate
should be closely combined, and the three adjusting screws should be on
the same horizontal plane.
2. Please fill the oil
tank before using the machine. Do not idle the machine for more than 2
minutes.
3.Double-check the belt
and the screws before operation.
4.Clean up the rest after use to prevent damage to the machine.
5.If the pressure roller cannot rotate normally, please tighten the
screws that control the pressure roller first, and then try to power it
on. If it still does not work, you can appropriately loosen the screws
next to the pressure roller and then tighten them slightly again
(without special tightening)
|
|
Product parameter: |
 |
|
Product analysis: |
 |
|
Feature: |
 |
This machine is equipped with an
enlarged and widened discharge port to prevent feed splashing and
facilitate the collection of feed by customers. |
|
This machine is equipped with a voltage
display, which can visually see whether the voltage is stable. |
 |
 |
Adjustable nut Used to
adjust the distance between the pressure roller and the grinding disc.
When making pellets, the nuts on the three sides must be balanced to
avoid damage to the pressure roller and grinding disc.
If the pressure roller cannot rotate normally, please tighten the screws
that control the pressure roller first, and then try to power it on. If
it still does not work, you can appropriately loosen the screws next to
the pressure roller and then tighten them slightly again (without
special tightening) |
|
Enlarge the feed inlet
The machine adopts the design of
enlarged feed port, which makes it more convenient for you to feed and
effectively improves work efficiency. |
 |
 |
Here is the filling port, open here to
add engine oil It is
recommended to add high-quality machine oil or hyperbola heavy-duty gear
oil. |
|
The length of feed particlescan be
adjusted here. |
 |
 |
The machine is equipped with air
switch, which is safer to use. |
|
Nylon wheels are adopted, which are
more wear-resistant and durable. |
 |
 |
After using the machine for a period of
time, the customer needs to add butter to lubricate the grinding chamber
here (approximately 4-6 months of use) (the butter gun and butter need
to be purchased by the customer themselves, and we do not provide them). |
 |
 |
|
Precautions:
|
|
1.When using, it
should be noted that there should be no foreign matter such as stones
and ironblocks in the raw materials. After the pellet machine has been
working continuously for morethan ten shifts, the pressure roller oil
hole, the universal joint oil hole, and the linkage shaft oilhole need
to be filled with high-temperature lubricating grease to make the
pressure roller Goodworking performance and extended bearing life.
2.During granulation, it is strictly forbidden for the pressure roller
to contact with the templateto run idly, and the continuous feeding can
not be interrupted.At the same time, the pressureroller shaft nut is
locked to avoid loosening and damaging the spindle keyway.
3.When granulating, there is no granulation, no discharge, the
template should be removed, andafter opening one by one, some fiber feed
can be added appropriately to restart the granulation.
4.Always check
the tightness of the screws in each part of the machine. If there is oil
leakage inthe gearbox, replace the oil seals in time, and check whether
the bearings in the machine headare short of oil.
5.When the pellet machine is working, do not reach into the feeding
port with your hands. Ifnecessary, use wooden sticks to help feed the
pellets.
6.Before turning on the machine, it is necessary to add less material
before turning on the
machine. When shutting down, leave a small amount
of feed in the machine to prevent the pressroller of the machine from
contacting the template from idling.
7.If the machine is stuck in operation, stop it immediately, press the
pressure roller until thebolt is flat,and then restart the machine.
8.Each time the work is completed, the adjusting pressure roller bolts
must be loosened.
9.Iron or stones cannot be put into the griller.
10.Check the elasticity of the belt, and the bearing frequently. Add oil
in time when it needs to.
|
|
Note:
We suggest that
high-power machines should be directly connected to the main power
supply, as the voltage reaching the machine is stable. If the voltage is
unstable and the current exceeds the rated current of the motor, it is
easy to burn out the starting capacitor.
It is recommended to
directly connect to the power supply as much as possible. If the machine
is not connected to the power supply, different situations may occur,
and the wires are not durable. The wires will gradually burn out over
time.
|
 |
|
Details: |
 |
|
 |
 |
|
Usage and specification:
|
|
1: It applies to chicken industry.
2:Corn particles can be put into the machine
directly. The feed processed by the machine is smooth and has moderate
hardness. The temperature-change during the process is slight so the
nutrition can be contained very well.
3:The practical’s diameter of the holes can be
divided into: Φ2, Φ3, Φ4, Φ5, Φ6, Φ8,
Φ10, Φ12.
4:The microorganism and parasite can be killed
during the process by extrusion.
|
|
Operating principle and product
advantages: |
|
Small feed
granulator, also known as small household feed granulator, is based on
the principle of circular motion. The template and pressure roller are
made of high-quality chrome-manganese titanium and are specially
treated. The main shaft and flat mold drive the pressure roller to
rotate under the action of friction. The materials are gelatinized at
high temperature between the pressure roller and the template, and the
protein is solidified and denatured. The particles are discharged from
the mold hole under the extrusion of the pressure roller. The particles
made are sent out of the machine through the throwing plate, and the
length of the particles can be adjusted through the incision.
This product
model is a new energy-saving product. In the past, the feed was usually
processed into powder and then fed, which had some defects such as
inconvenient feeding, poor palatability, picky eating of livestock, and
low utilization rate. With the advent and popularization of new small
pellet feed machinery, powder feed can be easily processed into pellet
feed. Lighting electricity can be used as the power to press the
granulation from the die hole under the extrusion of the press roller,
which can easily adjust the length of the granules. Its structure is
simple, the floor area is small, the noise is low, and it has many
advantages after processing into pellet feed.
|
|
Product display: |
 |
 |
 |
|
 |
 |
|
Item Number:
1*Chicken Feed Pellet Mill Machine 220V (239202) |
|
|
You can make order
with no worry.
Any concerns just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from us with low cost. |
|
