|
|
|
10L
Double-layer Glass Reaction Kettle 110V |
|
|
|
|
|
|
 |
|
Product
Overview |
| The
double-layer glass reactor is a piece of laboratory equipment
used for various biochemical reactions and synthesis reactions
under the constant temperature conditions. The whole system is
in a closed state and can be pumped to a negative pressure state
as needed to meet the experimental production conditions. The
constant pressure funnel regulating valve is adjusted to control
the uniform droplet addition of materials, and the reaction
products can be distilled and recovered by use of the heat
exchange function of the condenser. The double-layer glass
reactor is mainly used for the stirring experiment, synthesis
experiment, distillation experiment, concentration experiment
and other experiments. The kettle body is made of double-layer
transparent glass, the reaction process is clear at a glance,
the interlayer is hollow, and the reactor can be used for
refrigeration and heating experiments through other equipment.
The double-layer glass reactor can be matched with vacuum pumps,
high-temperature circulating baths, low-temperature coolant
circulating pumps, high and low temperature integrated machines
and so on. |
|
|
Product
Parameters |
| Voltage |
110V 60Hz |
| Power |
90W |
|
Speed |
0-500 revolutions per minute |
|
Speed regulation method |
Infinite
speed regulation, with speed and temperature digital display
function |
|
Interior available
capacity of reactor |
10L |
|
Interlayer capacity |
3L |
|
Glass material |
GG17 high borosilicate glass |
| Thickness
of kettle body |
≥5mm |
|
Tolerable temperature
of reaction kettle body |
-100~250˚C (The excessive temperature difference
is prohibited.) |
|
Pressure of reaction
kettle |
-0.098MPA |
| Use temperature of reaction
kettle |
-80~200˚C (The excessive temperature difference
is prohibited.) |
|
Sealing mode |
PTFE mechanical sealing and ceramic bearing |
|
Material of stirring
paddle |
304 stainless steel coated with PTFE |
|
Condenser |
S-shaped dual coil pipes, ground opening 40/29 |
|
Constant pressure
funnel |
1L |
|
Backflow bottle |
500ml |
|
 |
|
Attention |
|
1. Glass pieces
with serious stain can be cleaned with dilute sulfuric acid.
2. Check the
degree of wear (corrosion) of the sealing ring, and replace the wearing
part in time to ensure the vacuum degree of the equipment.
3. Clean the PTFE
discharge valve frequently to avoid blockage and pollution to the
material.
4. During
equipment operation, do not touch the transmission device to avoid
risks.
5. The firm
ground wire must be connected for the power supply.
6. The equipment
should be placed on the clean and flat ground, and the brake should be
pressed. Be careful to disassemble, clean and move the equipment to
avoid the phenomenon that the equipment falls down to be broken and hurt
people.
|
|
|
Product
Features |
 |
|
1. GG-17 high
borosilicate glass has good chemical and physical attributes.
2. Deceleration
stirrer, smooth operation, high
torque and no spark.
3. PTFE rotary
seal assembly, patented product, high vacuum degree and long service
life.
4. 201 stainless
steel frame with wheels and brakes.
5. PTFE
no-liquid-accumulation discharge valve, no leakage and no pollution to
the solvent.
6. Integrated
jacketed reaction flask with excellent sealing performance, and easy and
safe to clean.
7. S-shaped dual
coil pipes, high condensation efficiency.
|
|
|
|
|
|
|
Installation
Method |
|
1. Open the
packing case and check all components.
2. Take out the
stainless steel frame, then put it on the ground and make sure the
brakes are closed.
3. Fix the main
rod, the condenser supporting rod and all connection rods.
4. Install the
motor and speed controller.
5. Install mixing
sealing components on the reactor cover and mount a stirring rod. The
reactor cover is buckled on the reactor body, and the aluminium pot
cover is fixed to the kettle. (When you install the cover, the sealed
surface is coated with a little vacuum grease, and it can effectively
reduce the neck wear and improve the vacuum degree.)
6. Install all
glass components. (Put the vacuum grease on the seal coating).
7. Install the
discharge valve.
8. Check all the
installation steps once more. Power on and test the machine.
9. Installation
steps: Firstly, fix the middle shelf at the scale line position. Install
the kettle body, and fix the kettle body and the kettle cover. Install
the stirring plug, insert the stirring rod, connect it with the kettle
body and fix it. Install the motor, connect the stirring rod and try to
keep vertical in the installation process, so the stirring process is
not prone to shake. After fixing the motor, install the backflow bottle,
the condenser, the constant pressure funnel and the valve in turn.
If you need an
installation video, please contact the store where you purchase the
equipment.
|
|
|
Operation Method |
|
1. Check the
power supply voltage, and make sure it is consistent with the
specifications on the nameplate.
2. Plug in the
machine, turn on the power switch on the frequency converter, and adjust
the speed through the controller.
3. Please change
the speed of the motor to avoid the resonance which is always caused by
the flow of material and the motor at the same time.
4.
After installing the stirring rod, rotate it with your hand to make sure
the position
is right. If the position is improper, install it again.
5. If sealing
performance is bad,
please check the sealing part inside the bearing.
|
|
|
Product
Display |
 |
 |
|
Item Number (220590): 1 x
Double-layer Glass Reaction Kettle 10L 110V |
|
|
You can make
order with no worry.
Any concern just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from us with low cost. |
|
